micropython/espflash: A minimal ESP32 bootloader protocol implementation.

micropython/espflash/espflash.py

@@ -0,0 +1,308 @@
+# This file is part of the MicroPython project, http://micropython.org/
+#
+# The MIT License (MIT)
+#
+# Copyright (c) 2022 Ibrahim Abdelkader <[email protected]>
+#
+# Permission is hereby granted, free of charge, to any person obtaining a copy
+# of this software and associated documentation files (the "Software"), to deal
+# in the Software without restriction, including without limitation the rights
+# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+# copies of the Software, and to permit persons to whom the Software is
+# furnished to do so, subject to the following conditions:
+#
+# The above copyright notice and this permission notice shall be included in
+# all copies or substantial portions of the Software.
+#
+# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+# THE SOFTWARE.
+#
+# A minimal esptool implementation to communicate with ESP32 ROM bootloader.
+# Note this tool does Not support advanced features, other ESP chips or stub loading.
+# This is only meant to be used for updating the U-blox Nina module firmware.
+
+import os
+import struct
+from micropython import const
+from time import sleep
+import binascii
+
+_CMD_SYNC = const(0x08)
+_CMD_CHANGE_BAUDRATE = const(0x0F)
+
+_CMD_ESP_READ_REG = const(0x0A)
+_CMD_ESP_WRITE_REG = const(0x09)
+
+_CMD_SPI_ATTACH = const(0x0D)
+_CMD_SPI_FLASH_MD5 = const(0x13)
+_CMD_SPI_FLASH_PARAMS = const(0x0B)
+_CMD_SPI_FLASH_BEGIN = const(0x02)
+_CMD_SPI_FLASH_DATA = const(0x03)
+_CMD_SPI_FLASH_END = const(0x04)
+
+_FLASH_ID = const(0)
+_FLASH_REG_BASE = const(0x60002000)
+_FLASH_BLOCK_SIZE = const(64 * 1024)
+_FLASH_SECTOR_SIZE = const(4 * 1024)
+_FLASH_PAGE_SIZE = const(256)
+
+_ESP_ERRORS = {
+    0x05: "Received message is invalid",
+    0x06: "Failed to act on received message",
+    0x07: "Invalid CRC in message",
+    0x08: "Flash write error",
+    0x09: "Flash read error",
+    0x0A: "Flash read length error",
+    0x0B: "Deflate error",
+}
+
+
+class ESPFlash:
+    def __init__(self, reset, gpio0, uart, log_enabled=False):
+        self.uart = uart
+        self.reset_pin = reset
+        self.gpio0_pin = gpio0
+        self.log = log_enabled
+        self.baudrate = 115200
+        self.md5sum = None
+        try:
+            import hashlib
+
+            if hasattr(hashlib, "md5"):
+                self.md5sum = hashlib.md5()
+        except ImportError:
+            pass
+
+    def _log(self, data, out=True):
+        if self.log:
+            size = len(data)
+            print(
+                f"out({size}) => " if out else f"in({size})  <= ",
+                "".join("%.2x" % (i) for i in data[0:10]),
+            )
+
+    def _uart_drain(self):
+        while self.uart.read(1) is not None:
+            pass
+
+    def _read_reg(self, addr):
+        v, d = self._command(_CMD_ESP_READ_REG, struct.pack("<I", _FLASH_REG_BASE + addr))
+        if d[0] != 0:
+            raise Exception("Command ESP_READ_REG failed.")
+        return v
+
+    def _write_reg(self, addr, data, mask=0xFFFFFFFF, delay=0):
+        v, d = self._command(
+            _CMD_ESP_WRITE_REG, struct.pack("<IIII", _FLASH_REG_BASE + addr, data, mask, delay)
+        )
+        if d[0] != 0:
+            raise Exception("Command ESP_WRITE_REG failed.")
+
+    def _poll_reg(self, addr, flag, retry=10, delay=0.050):
+        for i in range(0, retry):
+            reg = self._read_reg(addr)
+            if (reg & flag) == 0:
+                break
+            sleep(delay)
+        else:
+            raise Exception(f"Register poll timeout. Addr: 0x{addr:02X} Flag: 0x{flag:02X}.")
+
+    def _write_slip(self, pkt):
+        pkt = pkt.replace(b"\xDB", b"\xdb\xdd").replace(b"\xc0", b"\xdb\xdc")
+        self.uart.write(b"\xC0" + pkt + b"\xC0")
+        self._log(pkt)
+
+    def _read_slip(self):
+        pkt = None
+        # Find the packet start.
+        if self.uart.read(1) == b"\xC0":
+            pkt = bytearray()
+            while True:
+                b = self.uart.read(1)
+                if b is None or b == b"\xC0":
+                    break
+                pkt += b
+            pkt = pkt.replace(b"\xDB\xDD", b"\xDB").replace(b"\xDB\xDC", b"\xC0")
+            self._log(b"\xC0" + pkt + b"\xC0", False)
+        return pkt
+
+    def _strerror(self, err):
+        if err in _ESP_ERRORS:
+            return _ESP_ERRORS[err]
+        return "Unknown error"
+
+    def _checksum(self, data):
+        checksum = 0xEF
+        for i in data:
+            checksum ^= i
+        return checksum
+
+    def _command(self, cmd, payload=b"", checksum=0):
+        self._write_slip(struct.pack(b"<BBHI", 0, cmd, len(payload), checksum) + payload)
+        for i in range(10):
+            pkt = self._read_slip()
+            if pkt is not None and len(pkt) >= 8:
+                (flag, _cmd, size, val) = struct.unpack("<BBHI", pkt[:8])
+                if flag == 1 and cmd == _cmd:
+                    status = list(pkt[-4:])
+                    if status[0] == 1:
+                        raise Exception(f"Command {cmd} failed {self._strerror(status[1])}")
+                    return val, pkt[8:]
+        raise Exception(f"Failed to read response to command {cmd}.")
+
+    def set_baudrate(self, baudrate, timeout=350):
+        if not hasattr(self.uart, "init"):
+            return
+        if baudrate != self.baudrate:
+            print(f"Changing baudrate => {baudrate}")
+            self._uart_drain()
+            self._command(_CMD_CHANGE_BAUDRATE, struct.pack("<II", baudrate, 0))
+            self.baudrate = baudrate
+        self.uart.init(baudrate)
+        self._uart_drain()
+
+    def bootloader(self, retry=6):
+        for i in range(retry):
+            self.gpio0_pin(1)
+            self.reset_pin(0)
+            sleep(0.1)
+            self.gpio0_pin(0)
+            self.reset_pin(1)
+            sleep(0.1)
+            self.gpio0_pin(1)
+
+            if "POWERON_RESET" not in self.uart.read():
+                continue
+
+            for i in range(10):
+                self._uart_drain()
+                try:
+                    # 36 bytes: 0x07 0x07 0x12 0x20, followed by 32 x 0x55
+                    self._command(_CMD_SYNC, b"\x07\x07\x12\x20" + 32 * b"\x55")
+                    self._uart_drain()
+                    return True
+                except Exception as e:
+                    print(e)
+
+        raise Exception("Failed to enter download mode!")
+
+    def flash_read_size(self):
+        SPI_REG_CMD = 0x00
+        SPI_USR_FLAG = 1 << 18
+        SPI_REG_USR = 0x1C
+        SPI_REG_USR2 = 0x24
+        SPI_REG_W0 = 0x80
+        SPI_REG_DLEN = 0x2C
+
+        # Command bit len | command
+        SPI_RDID_CMD = ((8 - 1) << 28) | 0x9F
+        SPI_RDID_LEN = 24 - 1
+
+        # Save USR and USR2 registers
+        reg_usr = self._read_reg(SPI_REG_USR)
+        reg_usr2 = self._read_reg(SPI_REG_USR2)
+
+        # Enable command phase and read phase.
+        self._write_reg(SPI_REG_USR, (1 << 31) | (1 << 28))
+
+        # Configure command.
+        self._write_reg(SPI_REG_DLEN, SPI_RDID_LEN)
+        self._write_reg(SPI_REG_USR2, SPI_RDID_CMD)
+
+        self._write_reg(SPI_REG_W0, 0)
+        # Trigger SPI operation.
+        self._write_reg(SPI_REG_CMD, SPI_USR_FLAG)
+
+        # Poll CMD_USER flag.
+        self._poll_reg(SPI_REG_CMD, SPI_USR_FLAG)
+
+        # Restore USR and USR2 registers
+        self._write_reg(SPI_REG_USR, reg_usr)
+        self._write_reg(SPI_REG_USR2, reg_usr2)
+
+        flash_bits = int(self._read_reg(SPI_REG_W0)) >> 16
+        if flash_bits < 0x12 or flash_bits > 0x19:
+            raise Exception(f"Unexpected flash size bits: 0x{flash_bits:02X}.")
+
+        flash_size = 2**flash_bits
+        print(f"Flash size {flash_size/1024/1024} MBytes")
+        return flash_size
+
+    def flash_attach(self):
+        self._command(_CMD_SPI_ATTACH, struct.pack("<II", 0, 0))
+        print(f"Flash attached")
+
+    def flash_config(self, flash_size=2 * 1024 * 1024):
+        self._command(
+            _CMD_SPI_FLASH_PARAMS,
+            struct.pack(
+                "<IIIIII",
+                _FLASH_ID,
+                flash_size,
+                _FLASH_BLOCK_SIZE,
+                _FLASH_SECTOR_SIZE,
+                _FLASH_PAGE_SIZE,
+                0xFFFF,
+            ),
+        )
+
+    def flash_write_file(self, path, blksize=0x1000):
+        size = os.stat(path)[6]
+        total_blocks = (size + blksize - 1) // blksize
+        erase_blocks = 1
+        print(f"Flash write size: {size} total_blocks: {total_blocks} block size: {blksize}")
+        with open(path, "rb") as f:
+            seq = 0
+            subseq = 0
+            for i in range(total_blocks):
+                buf = f.read(blksize)
+                # Update digest
+                if self.md5sum is not None:
+                    self.md5sum.update(buf)
+                # The last data block should be padded to the block size with 0xFF bytes.
+                if len(buf) < blksize:
+                    buf += b"\xFF" * (blksize - len(buf))
+                checksum = self._checksum(buf)
+                if seq % erase_blocks == 0:
+                    # print(f"Erasing {seq} -> {seq+erase_blocks}...")
+                    self._command(
+                        _CMD_SPI_FLASH_BEGIN,
+                        struct.pack(
+                            "<IIII", erase_blocks * blksize, erase_blocks, blksize, seq * blksize
+                        ),
+                    )
+                print(f"Writing sequence number {seq}/{total_blocks}...")
+                self._command(
+                    _CMD_SPI_FLASH_DATA,
+                    struct.pack("<IIII", len(buf), seq % erase_blocks, 0, 0) + buf,
+                    checksum,
+                )
+                seq += 1
+
+        print("Flash write finished")
+
+    def flash_verify_file(self, path, digest=None, offset=0):
+        if digest is None:
+            if self.md5sum is None:
+                raise Exception(f"MD5 checksum missing.")
+            digest = binascii.hexlify(self.md5sum.digest())
+
+        size = os.stat(path)[6]
+        val, data = self._command(_CMD_SPI_FLASH_MD5, struct.pack("<IIII", offset, size, 0, 0))
+
+        print(f"Flash verify: File  MD5 {digest}")
+        print(f"Flash verify: Flash MD5 {bytes(data[0:32])}")
+
+        if digest == data[0:32]:
+            print("Firmware verified.")
+        else:
+            raise Exception(f"Firmware verification failed.")
+
+    def reboot(self):
+        payload = struct.pack("<I", 0)
+        self._write_slip(struct.pack(b"<BBHI", 0, _CMD_SPI_FLASH_END, len(payload), 0) + payload)

micropython/espflash/example.py

@@ -0,0 +1,29 @@
+import espflash
+from machine import Pin
+from machine import UART
+
+if __name__ == "__main__":
+    reset = Pin(3, Pin.OUT)
+    gpio0 = Pin(2, Pin.OUT)
+    uart = UART(1, 115200, tx=Pin(8), rx=Pin(9), timeout=350)
+
+    md5sum = b"9a6cf1257769c9f1af08452558e4d60e"
+    path = "NINA_W102-v1.5.0-Nano-RP2040-Connect.bin"
+
+    esp = espflash.ESPFlash(reset, gpio0, uart)
+    # Enter bootloader download mode, at 115200
+    esp.bootloader()
+    # Can now chage to higher/lower baudrate
+    esp.set_baudrate(921600)
+    # Must call this first before any flash functions.
+    esp.flash_attach()
+    # Read flash size
+    size = esp.flash_read_size()
+    # Configure flash parameters.
+    esp.flash_config(size)
+    # Write firmware image from internal storage.
+    esp.flash_write_file(path)
+    # Compares file and flash MD5 checksum.
+    esp.flash_verify_file(path, md5sum)
+    # Resets the ESP32 chip.
+    esp.reboot()

micropython/espflash/manifest.py

@@ -0,0 +1,6 @@
+metadata(
+    version="0.1",
+    description="Provides a minimal ESP32 bootloader protocol implementation.",
+)
+
+module("espflash.py")