Skip to content

FrYakaTKoP/simple-octo-ws2812

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

27 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

simple ESP8266 based Octoprint Printer State Lamp

Simple Sketch to display the printer state connected to Octoprint on a Neopixel (WS2812b or similar)

This is just a placeholder until a planned octoprint plugin is avialable. It polls the Ocotoprint REST API periodically via a HTTP GET request. There are some delay between the real state of the printer and the of the LED, this comes do the simple polling approch. Faster polling result in lower delay but also increases the load on the ESP and on the wifi or network in general (on Octoprint too).

Security Warning: This sketch sends unencrypted GET requests with the octoprint apikey in cleartext in the request header through your network. Although this isn't that big of a security risk though, if your octoprint is not visible to the internet (which i did not recommend anyway)

Description:

The color of the lamp will show you the status as follows:

-flash white: booting / connecting
-fade rainbow: Printer is ready
-fade yellow: Printer is printing
-fade blue: Print is paused
-fade red: error occurred
-red/blue: HTTP Code Unauthorized
-fade green: HTTP Code Conflict

It will also output small informations on the serial line.

Hardware

Electronics

BOM:

  • 1x Wemos d1 mini (or any esp8266 with 4Mb flash)
  • 1x WS2812b RGB Led
  • 1x Wires (3 cores, about 3-4cm)
  • 1x Micro USB Cable and 5V Power supply schematic

Printed Parts

For best results using this Sketch in combination with the almighty Illumination Cat found on thingiverse is recommended.

https://www.thingiverse.com/thing:2974862

Software Installation

The Software is written especially for the ESP8266 from Espressif, using the Arduino Framework. There are two ways to setup the Development Environment and then flash the Software to the ESP8266

  • First and recommended is platform.io installed in the Atom Editor (you could use any platformio compatible editor, even pure cli)
  • Second is Arduino IDE with ESP8266 Core.

Also before you can upload any sketch to the wemos you will need to install the correct driver for the USB to serial converter chip on the wemos module.
This can be found here: https://wiki.wemos.cc/downloads

The Platform.io way (recommended)

  • Download/Clone this Repository and unpack it on your favourite folder

  • Download and install Atom Editor and the platformio IDE Package.. http://docs.platformio.org/en/latest/ide/atom.html#installation

  • when platformio is up an running, open the Project with File -> Open Folder (browse the unpacked repository then click select folder)
    open folder

  • Click PlatformIO: Build
    pio build
    Now platformio will download the needed dependencies (you need to be connected to the Internet)
    pio build success

  • After PIO Build is finished you can now change the User settings in the /src/config.h file according {TBD} link to config description

  • Click PlatformIO: Upload to upload the sketch to the ESP you may need to try the upload a couple times, those modules can be hard to program via bootloader. You could also check the connection using the serial monitor pio upload

  • enjoy {TBD} add pic of the almighty Illumination Cat in all its glory

The Arduino IDE Way

001
Then open Tools>Board>Boards Manager Search for ESP Install latest ESP8266 Board Manager 002

  • Add Additional Libraries Therefore open Sketch>Include Library>Manage Libraries... Search for Adafruit Neopixel Install latest Adafruit Neopixel library 003
    Search ArduinoJson Install latest ArduinoJson 004
  • Restart Arduino IDE
  • Open config.h and add your configuration
  • Choose your board and com port
  • Upload

Configuration

There are 4 main configurations in the config.h file, which must be made by user...

  1. Wifi SSID const char* SSID = "myWifi"; the name of your Wireless Network

  2. Wifi Password const char* SSID = "myWifi"; the password to your Wireless Network

  3. Octoprint API key const char* APIKEY = "FA9131811AF94AB48C6A9ED45AEF60FC"; like a password to the Octoprint REST Api {TBD} /doc/img/sc-octocprint-api-key.PNG You can obtain your API key in the Octoprint Webinterface in the settings under API. More info about the Octoprint API key in the API Documentation: link

  4. Octoprint Ip Address the Network address to your Octoprint. Same as you need to gain acces to your web interface of octoprint.

Example User Config:

#define LEDPIN D2 // where you Led is connected
const char* SSID = "myWifi";
const char* WPWD = "wifipassword";
const char* APIKEY = "FA9131811AF94AB48C6A9ED45AEF60FC";
String OCTOIP = "192.168.1.3";
uint16_t pollInterval = 500;
const uint8_t lenght = 1;

Releases

No releases published

Packages

No packages published