brcmfmac firmware error kernel: brcmfmac: brcmf_sdio_htclk: HT Avail request error: -5

[samveen]

My Zero2W had been up and running for close to 9 days, when the wifi firrmware gave errors and broke my connection to it today. With wifi connectivity shot, I triggered it's graceful shutdown to capture logs, and then booted it up again. I do not have more details than as below, as the log volume was large enough to exceed my log storage (log2ram lzo compressed ramdisk of 100M), and previous logs were rotated out.

All date and timestamps are IST (Kolkata +05:30) timezone.

The error messages I found (first, duplicate error lines, last; each kernel message misses the same error message multiple times, so actual number is much larger):

samveen@zero2w:~$ sudo journalctl -n 50000000 |grep -E 'brcmfmac: brcmf_sdio_htclk:|Missed [0-9]+ kernel messages' |head -n2
Aug 22 12:16:56 zero2w.cluster.samveen.in systemd-journald[454]: Missed 10 kernel messages
Aug 22 12:16:56 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_htclk: HT Avail request error: -5

samveen@zero2w:~$ sudo journalctl -n 50000000 |grep -E 'brcmfmac: brcmf_sdio_htclk:|Missed [0-9]+ kernel messages' |wc -l
28973

samveen@zero2w:~$ sudo journalctl -n 50000000 |grep -E 'brcmfmac: brcmf_sdio_htclk:|Missed [0-9]+ kernel messages' |tail -n2
Aug 22 12:37:07 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_htclk: HT Avail request error: -5
Aug 22 12:37:07 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_htclk: HT Avail request error: -5

EDIT
Another crash

Aug 22 17:49:59 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_isr: failed backplane access
Aug 22 17:49:59 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_readframes: RXHEADER FAILED: -110
Aug 22 17:49:59 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_rxfail: abort command, terminate frame, send NAK
Aug 22 17:49:59 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_isr: failed backplane access
Aug 22 17:50:02 zero2w.cluster.samveen.in kernel: ieee80211 phy0: brcmf_fw_crashed: Firmware has halted or crashed
Aug 22 17:50:02 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_bus_get_memdump: error -5 on reading 2048 membytes at 0x00000000
Aug 22 17:50:02 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_hostmail: Version mismatch, dongle reports 255, expecting 4
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_readshared: unable to obtain sdpcm_shared info: rv=-5 (addr=0x0)
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_hostmail: Unknown mailbox data content: 0xffffffff
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_txfail: sdio error, abort command and terminate frame
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: ieee80211 phy0: brcmf_cfg80211_dump_station: BRCMF_C_GET_ASSOCLIST failed, err=-5
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_dpc: failed backplane access over SDIO, halting operation
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_sdio_dpc: failed backplane access over SDIO, halting operation
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: ieee80211 phy0: brcmf_fil_cmd_data: bus is down. we have nothing to do.
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: ieee80211 phy0: brcmf_cfg80211_get_tx_power: error (-5)
Aug 22 17:50:05 zero2w.cluster.samveen.in wpa_supplicant[564]: wlan0: CTRL-EVENT-DISCONNECTED bssid=c0:06:c3:c2:d9:58 reason=1 locally_generated=1
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: ieee80211 phy0: brcmf_fil_cmd_data: bus is down. we have nothing to do.
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: ieee80211 phy0: brcmf_cfg80211_reg_notifier: Country code iovar returned err = -5
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: ieee80211 phy0: brcmf_fil_cmd_data: bus is down. we have nothing to do.
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: ieee80211 phy0: brcmf_cfg80211_reg_notifier: Country code iovar returned err = -5
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: mmc1: card 0001 removed
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: mmc1: new high speed SDIO card at address 0001
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: brcmfmac: F1 signature read @0x18000000=0x1541a9a6
Aug 22 17:50:05 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
Aug 22 17:50:06 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_c_process_txcap_blob: no txcap_blob available (err=-2)
Aug 22 17:50:06 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/1 wl0: Jun 14 2023 07:27:45 version 7.45.96.s1 (gf031a129) FWID 01-70bd2af7 es7
Aug 22 17:50:06 zero2w.cluster.samveen.in wpa_supplicant[564]: p2p-dev-wlan0: CTRL-EVENT-DSCP-POLICY clear_all
Aug 22 17:50:07 zero2w.cluster.samveen.in dbus-daemon[461]: [system] Activating via systemd: service name='org.freedesktop.nm_dispatcher' unit='dbus-org.freedesktop.nm-dispatcher.service' requested by ':1.9' (uid=0 pid=563 comm="/usr/sbin/NetworkManager --no-daemon")
Aug 22 17:50:07 zero2w.cluster.samveen.in wpa_supplicant[564]: p2p-dev-wlan0: CTRL-EVENT-DSCP-POLICY clear_all
Aug 22 17:50:07 zero2w.cluster.samveen.in wpa_supplicant[564]: nl80211: deinit ifname=p2p-dev-wlan0 disabled_11b_rates=0
Aug 22 17:50:07 zero2w.cluster.samveen.in NetworkManager[563]: <warn>  [1724329207.3335] dns-sd-resolved[4464a2bfd4e5c34a]: send-updates SetLinkDomains@3 failed: GDBus Error:org.freedesktop.resolve1.NoSuchLink: Link 3 not known
Aug 22 17:50:07 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
Aug 22 17:50:07 zero2w.cluster.samveen.in wpa_supplicant[564]: Could not read interface p2p-dev-wlan0 flags: No such device
Aug 22 17:50:08 zero2w.cluster.samveen.in wpa_supplicant[564]: p2p-dev-wlan0: CTRL-EVENT-DSCP-POLICY clear_all
Aug 22 17:50:08 zero2w.cluster.samveen.in wpa_supplicant[564]: p2p-dev-wlan0: CTRL-EVENT-DSCP-POLICY clear_all
Aug 22 17:50:08 zero2w.cluster.samveen.in wpa_supplicant[564]: nl80211: deinit ifname=p2p-dev-wlan0 disabled_11b_rates=0
Aug 22 17:50:08 zero2w.cluster.samveen.in wpa_supplicant[564]: wlan0: CTRL-EVENT-DSCP-POLICY clear_all
Aug 22 17:50:08 zero2w.cluster.samveen.in wpa_supplicant[564]: wlan0: CTRL-EVENT-DSCP-POLICY clear_all
Aug 22 17:50:08 zero2w.cluster.samveen.in wpa_supplicant[564]: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Aug 22 17:50:09 zero2w.cluster.samveen.in systemd[1]: Starting NetworkManager-dispatcher.service - Network Manager Script Dispatcher Service...
Aug 22 17:50:09 zero2w.cluster.samveen.in systemd[1]: Starting systemd-rfkill.service - Load/Save RF Kill Switch Status...
Aug 22 17:50:11 zero2w.cluster.samveen.in dbus-daemon[461]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher'
Aug 22 17:50:11 zero2w.cluster.samveen.in systemd[1]: Started NetworkManager-dispatcher.service - Network Manager Script Dispatcher Service.
Aug 22 17:50:11 zero2w.cluster.samveen.in kernel: warning: `iwconfig' uses wireless extensions which will stop working for Wi-Fi 7 hardware; use nl80211
Aug 22 17:50:12 zero2w.cluster.samveen.in systemd[1]: Started systemd-rfkill.service - Load/Save RF Kill Switch Status.
Aug 22 17:50:14 zero2w.cluster.samveen.in kernel: brcmfmac: brcmf_cfg80211_set_power_mgmt: power save disabled
Aug 22 17:50:14 zero2w.cluster.samveen.in wpa_supplicant[564]: wlan0: Trying to associate with SSID 'Guava'
Aug 22 17:50:15 zero2w.cluster.samveen.in wpa_supplicant[564]: wlan0: Associated with c0:06:c3:c2:d9:58
Aug 22 17:50:15 zero2w.cluster.samveen.in wpa_supplicant[564]: wlan0: CTRL-EVENT-CONNECTED - Connection to c0:06:c3:c2:d9:58 completed [id=0 id_str=]
Aug 22 17:50:15 zero2w.cluster.samveen.in wpa_supplicant[564]: wlan0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
Aug 22 17:50:15 zero2w.cluster.samveen.in wpa_supplicant[564]: wlan0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=IN
Aug 22 17:50:15 zero2w.cluster.samveen.in systemd-resolved[456]: wlan0: Bus client set search domain list to: guava.samveen.in
Aug 22 17:50:15 zero2w.cluster.samveen.in systemd-resolved[456]: wlan0: Bus client set default route setting: yes
Aug 22 17:50:15 zero2w.cluster.samveen.in systemd-resolved[456]: wlan0: Bus client set DNS server list to: 192.168.1.1
Aug 22 17:50:16 zero2w.cluster.samveen.in ModemManager[562]: <info>  [base-manager] couldn't check support for device '/sys/devices/platform/soc/3f300000.mmcnr/mmc_host/mmc1/mmc1:0001/mmc1:0001:1': not supported by any plugin
Aug 22 17:50:18 zero2w.cluster.samveen.in systemd[1]: systemd-rfkill.service: Deactivated successfully.

Uptime:

samveen@zero2w:~$ last |grep reboot | head -n2 
reboot   system boot  6.6.31+rpt-rpi-v Thu Aug 22 14:03   still running
reboot   system boot  6.6.31+rpt-rpi-v Tue Aug 13 14:12 - 12:36 (8+22:24)

OS details:

samveen@zero2w:~$ uname -a && cat /etc/os-release
Linux zero2w.cluster.samveen.in 6.6.31+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.31-1+rpt1 (2024-05-29) aarch64 GNU/Linux
PRETTY_NAME="Debian GNU/Linux 12 (bookworm)"
NAME="Debian GNU/Linux"
VERSION_ID="12"
VERSION="12 (bookworm)"
VERSION_CODENAME=bookworm
ID=debian
HOME_URL="https://www.debian.org/"
SUPPORT_URL="https://www.debian.org/support"
BUG_REPORT_URL="https://bugs.debian.org/"

Firmware version:

samveen@zero2w:~$ apt list firmware-brcm80211 --installed && apt show firmware-brcm80211=1:20230625-2+rpt2  2>/dev/null |grep -E '^Package:|^Version:|^Status:|^Section:|^Source:|^Description:'
firmware-brcm80211/now 1:20230625-2+rpt2 all [installed,upgradable to: 1:20230625-2+rpt3]
^Description:'
Package: firmware-brcm80211
Version: 1:20230625-2+rpt2
Status: install ok installed
Section: non-free-firmware/kernel
Source: firmware-nonfree
Description: Binary firmware for Broadcom/Cypress 802.11 wireless cards

A newer update is available. I'll be installing it:

samveen@zero2w:~$ apt list firmware-brcm80211 --upgradable && apt show firmware-brcm80211  2>/dev/null |grep -E '^Package:|^Version:|^Status:|^Section:|^Source:|^Description:'
firmware-brcm80211/stable,stable 1:20230625-2+rpt3 all [upgradable from: 1:20230625-2+rpt2]
Package: firmware-brcm80211
Version: 1:20230625-2+rpt3
Section: non-free-firmware/kernel
Source: firmware-nonfree
Description: Binary firmware for Broadcom/Cypress 802.11 wireless cards

raspinfo output

samveen@zero2w:~$ raspinfo
System Information
------------------

Raspberry Pi Zero 2 W Rev 1.0
PRETTY_NAME="Debian GNU/Linux 12 (bookworm)"
NAME="Debian GNU/Linux"
VERSION_ID="12"
VERSION="12 (bookworm)"

Raspberry Pi reference 2022-04-04
Generated using pi-gen, https://github.com/RPi-Distro/pi-gen, 27a8050c3c06e567c794620394a8c2d74262a516, stage2

Linux zero2w.cluster.samveen.in 6.6.31+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.31-1+rpt1 (2024-05-29) aarch64 GNU/Linux
Revision	: 902120
Serial		: 000000003e9c8e61
Model		: Raspberry Pi Zero 2 W Rev 1.0
Throttled flag  : throttled=0x0
Camera          : supported=0 detected=0, libcamera interfaces=0

Videocore information
---------------------

May 24 2024 15:31:41 
Copyright (c) 2012 Broadcom
version 4942b7633c0ff1af1ee95a51a33b56a9dae47529 (clean) (release) (start_cd)

alloc failures:     0
compactions:        0
legacy block fails: 0


Filesystem information
----------------------
Filesystem     1K-blocks     Used Available Use% Mounted on
udev              197148        0    197148   0% /dev
tmpfs              47612      864     46748   2% /run
/dev/mmcblk0p2  61096368 20509252  38073300  36% /
tmpfs             238056        0    238056   0% /dev/shm
tmpfs               5120        0      5120   0% /run/lock
/dev/mmcblk0p1    258095    44103    213992  18% /boot/firmware
tmpfs              47608        0     47608   0% /run/user/1001

Filename				Type		Size		Used		Priority
/var/swap                               file		970748		0		-2

Package version information
---------------------------
raspberrypi-ui-mods:
  Installed: (none)
raspberrypi-sys-mods:
  Installed: 20240624
openbox:
  Installed: (none)
lxpanel:
  Installed: (none)
pcmanfm:
  Installed: (none)
rpd-plym-splash:
  Installed: (none)

Networking Information
----------------------

eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet6 y::y.y.y.y  prefixlen 64  scopeid 0x20<link>
        ether m.m.m.m  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 185  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet x.x.x.x  netmask x.x.x.x
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 170  bytes 15495 (15.1 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 170  bytes 15495 (15.1 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet x.x.x.x  netmask x.x.x.x  broadcast x.x.x.x
        inet6 fd9c:aee2:y::y.y.y.y  prefixlen 128  scopeid 0x0<global>
        inet6 y.y.y.y.y.y.y.y  prefixlen 64  scopeid 0x0<global>
        inet6 y::y.y.y.y  prefixlen 64  scopeid 0x20<link>
        ether m.m.m.m  txqueuelen 1000  (Ethernet)
        RX packets 7915  bytes 2464738 (2.3 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 9687  bytes 5283967 (5.0 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0


USB Information
---------------

/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc_otg/1p, 480M

Display Information
-------------------

Running Legacy framebuffer

Framebuffer: /dev/fb0

mode "720x480"
    geometry 720 480 720 480 16
    timings 0 0 0 0 0 0 0
    rgba 5/11,6/5,5/0,0/16
endmode

/usr/bin/raspinfo: line 103: tvservice: command not found

Audio Information
-------------------

aplay: device_list:274: no soundcards found...

null
    Discard all samples (playback) or generate zero samples (capture)

Unit pipewire.socket could not be found.
Unit pipewire.service could not be found.
Unit pulseaudio.service could not be found.
Unit pulseaudio.socket could not be found.

pactl not installed

config.txt
----------

aphy_params_current=819
arm_64bit=1
arm_freq=1000
arm_freq_min=600
audio_pwm_mode=514
auto_initramfs=1
camera_auto_detect=-1
config_hdmi_boost=5
core_freq=400
desired_osc_freq=0x331df0
disable_commandline_tags=2
disable_fw_kms_setup=-1
disable_l2cache=1
disable_overscan=1
display_hdmi_rotate=-1
display_lcd_rotate=-1
dphy_params_current=547
dvfs=3
enable_tvout=1
enable_uart=1
force_eeprom_read=1
force_pwm_open=1
framebuffer_depth=16
framebuffer_ignore_alpha=1
framebuffer_swap=1
gpu_freq=300
hdmi_enable_4kp60=-1
ignore_lcd=1
init_uart_clock=0x2dc6c00
max_framebuffers=2
over_voltage_avs=25000
pause_burst_frames=1
pciex4_reset=1
pmic_turbo_threshold=600
program_serial_random=1
sdram_freq=450
total_mem=512
hdmi_force_cec_address:0=65535
hdmi_force_cec_address:1=65535
hdmi_pixel_freq_limit:0=0x9a7ec80
device_tree=-
overlay_prefix=overlays/
hdmi_cvt:0=
hdmi_cvt:1=
hdmi_edid_filename:0=
hdmi_edid_filename:1=
hdmi_timings:0=
hdmi_timings:1=

cmdline.txt
-----------
coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 bcm2708_fb.fbwidth=720 bcm2708_fb.fbheight=480 bcm2708_fb.fbdepth=16 bcm2708_fb.fbswap=1 smsc95xx.macaddr=B8:27:EB:9C:8E:61 vc_mem.mem_base=0x1fa00000 vc_mem.mem_size=0x20000000  console=tty1 console=ttyAMA0,115200 root=PARTUUID=d65d6b68-02 rootfstype=ext4 fsck.repair=yes rootwait cfg80211.ieee80211_regdom=IN

pin configuration
-----------------

 0: ip    -- | hi // ID_SDA/GPIO0 = input
 1: ip    -- | hi // ID_SCL/GPIO1 = input
 2: a0    -- | hi // GPIO2 = SDA1
 3: a0    -- | hi // GPIO3 = SCL1
 4: ip    -- | hi // GPIO4 = input
 5: ip    -- | hi // GPIO5 = input
 6: ip    -- | hi // GPIO6 = input
 7: op -- -- | hi // GPIO7 = output
 8: op -- -- | hi // GPIO8 = output
 9: a0    -- | lo // GPIO9 = SPI0_MISO
10: a0    -- | lo // GPIO10 = SPI0_MOSI
11: a0    -- | lo // GPIO11 = SPI0_SCLK
12: ip    -- | lo // GPIO12 = input
13: op -- -- | hi // GPIO13 = output
14: a0    -- | hi // GPIO14 = TXD0
15: a0    -- | hi // GPIO15 = RXD0
16: op -- -- | hi // GPIO16 = output
17: op -- -- | hi // GPIO17 = output
18: op -- -- | hi // GPIO18 = output
19: a4    -- | lo // GPIO19 = SPI1_MISO
20: a4    -- | lo // GPIO20 = SPI1_MOSI
21: a4    -- | lo // GPIO21 = SPI1_SCLK
22: ip    -- | lo // GPIO22 = input
23: ip    -- | lo // GPIO23 = input
24: ip    -- | lo // GPIO24 = input
25: ip    -- | hi // GPIO25 = input
26: op -- -- | hi // GPIO26 = output
27: ip    -- | lo // GPIO27 = input
28: ip    -- | hi // HDMI_HPD_N/GPIO28 = input
29: op -- -- | hi // STATUS_LED_N/GPIO29 = output
30: ip    -- | hi // CTS0/GPIO30 = input
31: ip    -- | hi // RTS0/GPIO31 = input
32: ip    -- | hi // TXD0/GPIO32 = input
33: ip    -- | hi // RXD0/GPIO33 = input
34: a3    -- | lo // SD1_CLK/GPIO34 = SD1_CLK
35: a3    -- | hi // SD1_CMD/GPIO35 = SD1_CMD
36: a3    -- | hi // SD1_DATA0/GPIO36 = SD1_DAT0
37: a3    -- | hi // SD1_DATA1/GPIO37 = SD1_DAT1
38: a3    -- | hi // SD1_DATA2/GPIO38 = SD1_DAT2
39: a3    -- | hi // SD1_DATA3/GPIO39 = SD1_DAT3
40: op -- -- | lo // CAM_GPIO1/GPIO40 = output
41: op -- -- | hi // WL_ON/GPIO41 = output
42: op -- -- | lo // BT_ON/GPIO42 = output
43: a0    -- | hi // WIFI_CLK/GPIO43 = GPCLK2
44: ip    -- | hi // SDA0/GPIO44 = input
45: ip    -- | hi // SCL0/GPIO45 = input
46: ip    -- | hi // SMPS_SCL/GPIO46 = input
47: op -- -- | hi // SMPS_SDA/GPIO47 = output
48: a0    -- | lo // SD_CLK_R/GPIO48 = SD0_CLK
49: a0    -- | hi // SD_CMD_R/GPIO49 = SD0_CMD
50: a0    -- | lo // SD_DATA0_R/GPIO50 = SD0_DAT0
51: a0    -- | lo // SD_DATA1_R/GPIO51 = SD0_DAT1
52: a0    -- | lo // SD_DATA2_R/GPIO52 = SD0_DAT2
53: a0    -- | lo // SD_DATA3_R/GPIO53 = SD0_DAT3

vcdbg log messages
------------------

Fatal error: Could not determine logs location from Device Tree

dmesg log
---------

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 6.6.31+rpt-rpi-v8 ([email protected]) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Debian 1:6.6.31-1+rpt1 (2024-05-29)
[    0.000000] KASLR enabled
[    0.000000] random: crng init done
[    0.000000] Machine model: Raspberry Pi Zero 2 W Rev 1.0
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x000000001a400000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] OF: reserved mem: 0x000000001a400000..0x000000001e3fffff (65536 KiB) map reusable linux,cma
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000001effffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000001effffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001effffff]
[    0.000000] On node 0, zone DMA: 4096 pages in unavailable ranges
[    0.000000] percpu: Embedded 30 pages/cpu s85672 r8192 d29016 u122880
[    0.000000] pcpu-alloc: s85672 r8192 d29016 u122880 alloc=30*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: kernel page table isolation forced ON by KASLR
[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[    0.000000] CPU features: detected: ARM erratum 843419
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 bcm2708_fb.fbwidth=720 bcm2708_fb.fbheight=480 bcm2708_fb.fbdepth=16 bcm2708_fb.fbswap=1 smsc95xx.macaddr=m.m.m.m vc_mem.mem_base=0x1fa00000 vc_mem.mem_size=0x20000000  console=tty1 console=ttyAMA0,115200 root=PARTUUID=d65d6b68-02 rootfstype=ext4 fsck.repair=yes rootwait cfg80211.ieee80211_regdom=IN
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 124992
[    0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
[    0.000000] Memory: 394300K/507904K available (13376K kernel code, 2210K rwdata, 4264K rodata, 4864K init, 1083K bss, 48068K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 43180 entries in 169 pages
[    0.000000] ftrace: allocated 169 pages with 4 groups
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU event tracing is enabled.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] 	Rude variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: bcm2836_arm_irqchip_handle_irq
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000390] Console: colour dummy device 80x25
[    0.000407] printk: console [tty1] enabled
[    0.001313] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[    0.001361] pid_max: default: 32768 minimum: 301
[    0.001476] LSM: initializing lsm=capability,integrity
[    0.001730] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.001777] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.002798] cgroup: Disabling memory control group subsystem
[    0.004825] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.005000] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.005150] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.005504] rcu: Hierarchical SRCU implementation.
[    0.005530] rcu: 	Max phase no-delay instances is 1000.
[    0.007652] EFI services will not be available.
[    0.008136] smp: Bringing up secondary CPUs ...
[    0.008931] Detected VIPT I-cache on CPU1
[    0.009086] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.009967] Detected VIPT I-cache on CPU2
[    0.010075] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.010880] Detected VIPT I-cache on CPU3
[    0.010979] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.011097] smp: Brought up 1 node, 4 CPUs
[    0.011228] SMP: Total of 4 processors activated.
[    0.011253] CPU features: detected: 32-bit EL0 Support
[    0.011274] CPU features: detected: 32-bit EL1 Support
[    0.011298] CPU features: detected: CRC32 instructions
[    0.011437] CPU: All CPU(s) started at EL2
[    0.011472] alternatives: applying system-wide alternatives
[    0.014340] devtmpfs: initialized
[    0.027254] Enabled cp15_barrier support
[    0.027319] Enabled setend support
[    0.027559] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.027613] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.030821] pinctrl core: initialized pinctrl subsystem
[    0.031598] DMI not present or invalid.
[    0.032271] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.039647] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    0.040050] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.040648] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.040776] audit: initializing netlink subsys (disabled)
[    0.041128] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
[    0.041939] thermal_sys: Registered thermal governor 'step_wise'
[    0.042004] cpuidle: using governor menu
[    0.042341] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.042512] ASID allocator initialised with 32768 entries
[    0.043640] Serial: AMBA PL011 UART driver
[    0.049598] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.060942] raspberrypi-firmware soc:firmware: Attached to firmware from 2024-05-24T15:31:41, variant start_cd
[    0.064963] raspberrypi-firmware soc:firmware: Firmware hash is 4942b7633c0ff1af1ee95a51a33b56a9dae47529
[    0.072729] Modules: 2G module region forced by RANDOMIZE_MODULE_REGION_FULL
[    0.072767] Modules: 0 pages in range for non-PLT usage
[    0.072775] Modules: 517792 pages in range for PLT usage
[    0.077211] bcm2835-dma 3f007000.dma-controller: DMA legacy API manager, dmachans=0x1
[    0.078788] iommu: Default domain type: Translated
[    0.078817] iommu: DMA domain TLB invalidation policy: strict mode
[    0.080612] SCSI subsystem initialized
[    0.080898] usbcore: registered new interface driver usbfs
[    0.080969] usbcore: registered new interface driver hub
[    0.081056] usbcore: registered new device driver usb
[    0.081535] pps_core: LinuxPPS API ver. 1 registered
[    0.081561] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.081612] PTP clock support registered
[    0.083178] vgaarb: loaded
[    0.083825] clocksource: Switched to clocksource arch_sys_counter
[    1.704600] VFS: Disk quotas dquot_6.6.0
[    1.704700] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.704865] FS-Cache: Loaded
[    1.705175] CacheFiles: Loaded
[    1.716469] NET: Registered PF_INET protocol family
[    1.716782] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.718212] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.718271] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    1.718317] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    1.718411] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    1.718618] TCP: Hash tables configured (established 4096 bind 4096)
[    1.718917] MPTCP token hash table entries: 512 (order: 1, 12288 bytes, linear)
[    1.719007] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    1.719062] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    1.719278] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.719943] RPC: Registered named UNIX socket transport module.
[    1.719975] RPC: Registered udp transport module.
[    1.719996] RPC: Registered tcp transport module.
[    1.720016] RPC: Registered tcp-with-tls transport module.
[    1.720038] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.720085] PCI: CLS 0 bytes, default 64
[    1.720815] Trying to unpack rootfs image as initramfs...
[    1.724067] kvm [1]: IPA Size Limit: 40 bits
[    1.725888] kvm [1]: Hyp mode initialized successfully
[    1.729968] Initialise system trusted keyrings
[    1.730452] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[    1.730574] zbud: loaded
[    1.731710] NFS: Registering the id_resolver key type
[    1.731786] Key type id_resolver registered
[    1.731858] Key type id_legacy registered
[    1.731908] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.731937] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    1.732873] Key type asymmetric registered
[    1.732919] Asymmetric key parser 'x509' registered
[    1.733013] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.733359] io scheduler mq-deadline registered
[    1.733395] io scheduler kyber registered
[    1.733465] io scheduler bfq registered
[    1.736186] pinctrl-bcm2835 3f200000.gpio: GPIO_OUT persistence: yes
[    1.738155] bcm2708_fb soc:fb: FB found 1 display(s)
[    1.746543] Console: switching to colour frame buffer device 90x30
[    1.750294] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 720x480
[    1.755908] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    1.759756] bcm2835-rng 3f104000.rng: hwrng registered
[    1.761564] vc-mem: phys_addr:0x00000000 mem_base=0x1fa00000 mem_size:0x20000000(512 MiB)
[    1.784532] brd: module loaded
[    1.796534] loop: module loaded
[    1.798608] Loading iSCSI transport class v2.0-870.
[    1.805673] usbcore: registered new device driver r8152-cfgselector
[    1.806930] usbcore: registered new interface driver r8152
[    1.808199] usbcore: registered new interface driver lan78xx
[    1.809396] usbcore: registered new interface driver smsc95xx
[    1.810887] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    2.540570] Core Release: 2.80a
[    2.541694] Setting default values for core params
[    2.542786] Finished setting default values for core params
[    2.636208] Freeing initrd memory: 11416K
[    2.744328] Using Buffer DMA mode
[    2.745325] Periodic Transfer Interrupt Enhancement - disabled
[    2.746339] Multiprocessor Interrupt Enhancement - disabled
[    2.747371] OTG VER PARAM: 0, OTG VER FLAG: 0
[    2.748440] Dedicated Tx FIFOs mode

[    2.750078] WARN::dwc_otg_hcd_init:1072: FIQ DMA bounce buffers: virt = ffffffc080cfb000 dma = 0x00000000da810000 len=9024
[    2.753169] FIQ FSM acceleration enabled for :
               Non-periodic Split Transactions
               Periodic Split Transactions
               High-Speed Isochronous Endpoints
               Interrupt/Control Split Transaction hack enabled
[    2.757963] dwc_otg: Microframe scheduler enabled

[    2.758004] WARN::hcd_init_fiq:496: MPHI regs_base at ffffffc080065000
[    2.759993] dwc_otg 3f980000.usb: DWC OTG Controller
[    2.761009] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    2.762061] dwc_otg 3f980000.usb: irq 74, io mem 0x00000000
[    2.763131] Init: Port Power? op_state=1
[    2.764181] Init: Power Port (0)
[    2.765465] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[    2.767562] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.768702] usb usb1: Product: DWC OTG Controller
[    2.769810] usb usb1: Manufacturer: Linux 6.6.31+rpt-rpi-v8 dwc_otg_hcd
[    2.770944] usb usb1: SerialNumber: 3f980000.usb
[    2.772868] hub 1-0:1.0: USB hub found
[    2.774023] hub 1-0:1.0: 1 port detected
[    2.775780] dwc_otg: FIQ enabled
[    2.775789] dwc_otg: NAK holdoff enabled
[    2.775796] dwc_otg: FIQ split-transaction FSM enabled
[    2.775851] Module dwc_common_port init
[    2.776656] usbcore: registered new interface driver uas
[    2.777830] usbcore: registered new interface driver usb-storage
[    2.779426] mousedev: PS/2 mouse device common for all mice
[    2.783151] sdhci: Secure Digital Host Controller Interface driver
[    2.784259] sdhci: Copyright(c) Pierre Ossman
[    2.785502] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.788058] ledtrig-cpu: registered to indicate activity on CPUs
[    2.789495] hid: raw HID events driver (C) Jiri Kosina
[    2.790724] usbcore: registered new interface driver usbhid
[    2.791854] usbhid: USB HID core driver
[    2.793048] bcm2835_vchiq 3f00b840.mailbox: there is not valid maps for state default
[    2.799473] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    2.803039] NET: Registered PF_PACKET protocol family
[    2.804365] Key type dns_resolver registered
[    2.843855] registered taskstats version 1
[    2.845332] Loading compiled-in X.509 certificates
[    2.861531] Key type .fscrypt registered
[    2.862673] Key type fscrypt-provisioning registered
[    2.876134] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    2.877603] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    2.880243] mmc-bcm2835 3f300000.mmcnr: mmc_debug:0 mmc_debug2:0
[    2.881341] mmc-bcm2835 3f300000.mmcnr: DMA channel allocated
[    2.910657] sdhost: log_buf @ 00000000dd243b3d (c2896000)
[    2.961121] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    2.963151] uart-pl011 3f201000.serial: there is not valid maps for state default
[    2.964819] uart-pl011 3f201000.serial: cts_event_workaround enabled
[    2.966740] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 99, base_baud = 0) is a PL011 rev2
[    2.969505] printk: console [ttyAMA0] enabled
[    4.274868] of_cfs_init
[    4.279615] of_cfs_init: OK
[    4.284096] clk: Disabling unused clocks
[    4.289880] uart-pl011 3f201000.serial: no DMA platform data
[    4.308230] Freeing unused kernel memory: 4864K
[    4.314149] Run /init as init process
[    4.318900]   with arguments:
[    4.318908]     /init
[    4.318916]   with environment:
[    4.318922]     HOME=/
[    4.318930]     TERM=linux
[    4.332384] mmc0: host does not support reading read-only switch, assuming write-enable
[    4.346089] mmc0: Host Software Queue enabled
[    4.351696] mmc0: new high speed SDXC card at address aaaa
[    4.359775] mmcblk0: mmc0:aaaa SN64G 59.5 GiB
[    4.369057]  mmcblk0: p1 p2
[    4.374041] mmcblk0: mmc0:aaaa SN64G 59.5 GiB (quirks 0x00004000)
[    4.398920] mmc1: new high speed SDIO card at address 0001
[    5.029239] input: soc:shutdown_button@5 as /devices/platform/soc/soc:shutdown_button@5/input/input0
[    5.121530] enc28j60 spi0.0: Ethernet driver 1.02 loaded
[    5.145915] rtc-ds1307 1-0068: registered as rtc0
[    5.153973] rtc-ds1307 1-0068: setting system clock to 2024-08-22T08:33:53 UTC (1724315633)
[    5.711186] EXT4-fs (mmcblk0p2): mounted filesystem 6a932c1f-7335-42d9-9351-1b1b2ca538d4 ro with ordered data mode. Quota mode: none.
[    6.870440] NET: Registered PF_INET6 protocol family
[    6.878454] Segment Routing with IPv6
[    6.883389] In-situ OAM (IOAM) with IPv6
[    6.989847] systemd[1]: systemd 252.26-1~deb12u2 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    7.029129] systemd[1]: Detected architecture arm64.
[    7.064121] systemd[1]: Hostname set to <zero2w.cluster.samveen.in>.
[    8.376522] systemd[1]: Queued start job for default target graphical.target.
[    8.412072] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe.
[    8.442104] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty.
[    8.474067] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck.
[    8.505266] systemd[1]: Created slice user.slice - User and Session Slice.
[    8.532478] systemd[1]: Started systemd-ask-password-console.path - Dispatch Password Requests to Console Directory Watch.
[    8.564390] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch.
[    8.597194] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point.
[    8.632108] systemd[1]: Expecting device dev-disk-by\x2dpartuuid-d65d6b68\x2d01.device - /dev/disk/by-partuuid/d65d6b68-01...
[    8.664010] systemd[1]: Expecting device dev-ttyAMA0.device - /dev/ttyAMA0...
[    8.688069] systemd[1]: Reached target cryptsetup.target - Local Encrypted Volumes.
[    8.716179] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes.
[    8.744324] systemd[1]: Reached target paths.target - Path Units.
[    8.768213] systemd[1]: Reached target slices.target - Slice Units.
[    8.792168] systemd[1]: Reached target swap.target - Swaps.
[    8.816148] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes.
[    8.844935] systemd[1]: Listening on syslog.socket - Syslog Socket.
[    8.868820] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket.
[    8.896479] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe.
[    8.925689] systemd[1]: Listening on systemd-journald-audit.socket - Journal Audit Socket.
[    8.956851] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log).
[    8.989015] systemd[1]: Listening on systemd-journald.socket - Journal Socket.
[    9.017173] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket.
[    9.044763] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket.
[    9.073071] systemd[1]: dev-hugepages.mount - Huge Pages File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[    9.116296] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System...
[    9.149392] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System...
[    9.181310] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System...
[    9.208560] systemd[1]: auth-rpcgss-module.service - Kernel Module supporting RPCSEC_GSS was skipped because of an unmet condition check (ConditionPathExists=/etc/krb5.keytab).
[    9.252661] systemd[1]: Starting fake-hwclock.service - Restore / save the current clock...
[    9.286315] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout...
[    9.336818] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes...
[    9.370714] systemd[1]: Starting [email protected] - Load Kernel Module configfs...
[    9.420821] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod...
[    9.454669] systemd[1]: Starting [email protected] - Load Kernel Module drm...
[    9.488776] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore...
[    9.500280] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: [email protected]
[    9.560845] systemd[1]: Starting [email protected] - Load Kernel Module fuse...
[    9.600395] systemd[1]: Starting [email protected] - Load Kernel Module loop...
[    9.630019] fuse: init (API version 7.39)
[    9.645052] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root).
[    9.688690] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules...
[    9.726562] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems...
[    9.766607] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices...
[    9.813751] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System.
[    9.823800] EXT4-fs (mmcblk0p2): re-mounted 6a932c1f-7335-42d9-9351-1b1b2ca538d4 r/w. Quota mode: none.
[    9.857852] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System.
[    9.885198] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace File System.
[    9.916026] systemd[1]: Finished fake-hwclock.service - Restore / save the current clock.
[    9.945953] systemd[1]: Finished keyboard-setup.service - Set the console keyboard layout.
[    9.977973] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes.
[   10.010212] systemd[1]: [email protected]: Deactivated successfully.
[   10.020250] systemd[1]: Finished [email protected] - Load Kernel Module configfs.
[   10.050083] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[   10.064063] systemd[1]: Finished modprobe@dm_mod.service - Load Kernel Module dm_mod.
[   10.098383] systemd[1]: [email protected]: Deactivated successfully.
[   10.111999] systemd[1]: Finished [email protected] - Load Kernel Module drm.
[   10.145995] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[   10.156112] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore.
[   10.190088] systemd[1]: [email protected]: Deactivated successfully.
[   10.199485] systemd[1]: Finished [email protected] - Load Kernel Module fuse.
[   10.229974] systemd[1]: [email protected]: Deactivated successfully.
[   10.244057] systemd[1]: Finished [email protected] - Load Kernel Module loop.
[   10.279953] systemd[1]: Finished systemd-modules-load.service - Load Kernel Modules.
[   10.309989] systemd[1]: Finished systemd-remount-fs.service - Remount Root and Kernel File Systems.
[   10.341513] systemd[1]: Finished systemd-udev-trigger.service - Coldplug All udev Devices.
[   10.404319] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System...
[   10.437167] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System...
[   10.464184] systemd[1]: systemd-firstboot.service - First Boot Wizard was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[   10.480612] systemd[1]: systemd-pstore.service - Platform Persistent Storage Archival was skipped because of an unmet condition check (ConditionDirectoryNotEmpty=/sys/fs/pstore).
[   10.506763] systemd[1]: Starting systemd-random-seed.service - Load/Save Random Seed...
[   10.532587] systemd[1]: systemd-repart.service - Repartition Root Disk was skipped because no trigger condition checks were met.
[   10.553455] systemd[1]: Starting systemd-sysctl.service - Apply Kernel Variables...
[   10.624749] systemd[1]: Starting systemd-sysusers.service - Create System Users...
[   10.666291] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System.
[   10.684822] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System.
[   10.705934] systemd[1]: Finished systemd-random-seed.service - Load/Save Random Seed.
[   10.717561] systemd[1]: Finished systemd-sysctl.service - Apply Kernel Variables.
[   10.737591] systemd[1]: Finished systemd-sysusers.service - Create System Users.
[   10.757243] systemd[1]: first-boot-complete.target - First Boot Complete was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[   10.776714] systemd[1]: Starting systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev...
[   10.867149] systemd[1]: Finished systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev.
[   10.884984] systemd[1]: Reached target local-fs-pre.target - Preparation for Local File Systems.
[   10.928640] systemd[1]: Starting systemd-udevd.service - Rule-based Manager for Device Events and Files...
[   11.343118] systemd[1]: Started systemd-udevd.service - Rule-based Manager for Device Events and Files.
[   11.783388] systemd[1]: Found device dev-ttyAMA0.device - /dev/ttyAMA0.
[   11.961436] systemd[1]: Found device dev-disk-by\x2dpartuuid-d65d6b68\x2d01.device - /dev/disk/by-partuuid/d65d6b68-01.
[   12.014713] systemd[1]: Starting systemd-fsck@dev-disk-by\x2dpartuuid-d65d6b68\x2d01.service - File System Check on /dev/disk/by-partuuid/d65d6b68-01...
[   12.117033] systemd[1]: Started systemd-fsckd.service - File System Check Daemon to report status.
[   12.178077] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[   12.180655] rpi-gpiomem 3f200000.gpiomem: window base 0x3f200000 size 0x00001000
[   12.181650] rpi-gpiomem 3f200000.gpiomem: initialised 1 regions as /dev/gpiomem
[   12.190370] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[   12.190412] [vc_sm_connected_init]: start
[   12.194554] vc_sm_cma_vchi_init: failed to open VCHI service (-22)
[   12.194587] [vc_sm_connected_init]: failed to initialize shared memory service
[   12.229908] mc: Linux media interface: v0.10
[   12.463734] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[   12.512646] videodev: Linux video capture interface: v2.00
[   12.578629] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[   12.607182] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[   12.610169] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned.
[   12.627215] bcm2835_mmal_vchiq: Failed to open VCHI service connection (status=-22)
[   12.627253] bcm2835_mmal_vchiq: Failed to open VCHI service connection (status=-22)
[   12.627392] : Unregister from media controller
[   12.627406] (efault): Unregistering node (null)[0] device node /dev/video0
[   12.627420] (efault): Unregistering node (null)[0] device node /dev/video0
[   12.627432] (efault): Unregistering node (null)[0] device node /dev/video0
[   12.627444] (efault): Unregistering node (null)[0] device node /dev/video0
[   12.640622] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[   12.644239] bcm2835_mmal_vchiq: Failed to open VCHI service connection (status=-22)
[   12.821618] systemd[1]: Finished systemd-fsck@dev-disk-by\x2dpartuuid-d65d6b68\x2d01.service - File System Check on /dev/disk/by-partuuid/d65d6b68-01.
[   12.900653] systemd[1]: Mounting boot-firmware.mount - /boot/firmware...
[   12.946557] systemd[1]: Mounted boot-firmware.mount - /boot/firmware.
[   12.964999] systemd[1]: Reached target local-fs.target - Local File Systems.
[   12.980723] systemd[1]: apparmor.service - Load AppArmor profiles was skipped because of an unmet condition check (ConditionSecurity=apparmor).
[   13.025369] systemd[1]: Starting console-setup.service - Set console font and keymap...
[   13.051134] systemd[1]: Starting log2ram.service - Log2Ram...
[   13.078395] systemd[1]: Starting systemd-binfmt.service - Set Up Additional Binary Formats...
[   13.096517] systemd[1]: systemd-machine-id-commit.service - Commit a transient machine-id on disk was skipped because of an unmet condition check (ConditionPathIsMountPoint=/etc/machine-id).
[   13.098875] systemd[1]: Finished console-setup.service - Set console font and keymap.
[   13.142709] systemd[1]: proc-sys-fs-binfmt_misc.automount: Got automount request for /proc/sys/fs/binfmt_misc, triggered by 383 (systemd-binfmt)
[   13.180712] systemd[1]: Mounting proc-sys-fs-binfmt_misc.mount - Arbitrary Executable File Formats File System...
[   13.257690] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   13.262237] systemd[1]: Mounted proc-sys-fs-binfmt_misc.mount - Arbitrary Executable File Formats File System.
[   13.293910] systemd[1]: Finished systemd-binfmt.service - Set Up Additional Binary Formats.
[   13.305547] Loaded X.509 cert '[email protected]: 577e021cb980e0e820821ba7b54b4961b8b4fadf'
[   13.307099] Loaded X.509 cert '[email protected]: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
[   13.316755] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   13.318328] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[   13.404456] zram: Added device: zram0
[   13.413875] zram0: detected capacity change from 0 to 204800
[   13.512344] EXT4-fs (zram0): mounted filesystem 638139b9-930e-4d7d-8ccb-72e1b87616c3 r/w with ordered data mode. Quota mode: none.
[   13.681117] brcmfmac: F1 signature read @0x18000000=0x1541a9a6
[   13.700124] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
[   13.700869] usbcore: registered new interface driver brcmfmac
[   13.813626] EXT4-fs (zram0): unmounting filesystem 638139b9-930e-4d7d-8ccb-72e1b87616c3.
[   13.851396] systemd[1]: log2ram.service: Main process exited, code=exited, status=1/FAILURE
[   13.852532] systemd[1]: log2ram.service: Failed with result 'exit-code'.
[   13.853541] systemd[1]: Failed to start log2ram.service - Log2Ram.
[   13.941463] systemd[1]: Starting systemd-journald.service - Journal Service...
[   13.953604] brcmfmac: brcmf_c_process_txcap_blob: no txcap_blob available (err=-2)
[   13.954386] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/1 wl0: Jun 14 2023 07:27:45 version 7.45.96.s1 (gf031a129) FWID 01-70bd2af7 es7
[   13.963124] systemd[1]: var-log.mount: Deactivated successfully.
[   13.968404] systemd[1]: var-hdd.log.mount: Deactivated successfully.
[   14.140420] systemd[1]: Listening on systemd-rfkill.socket - Load/Save RF Kill Switch Status /dev/rfkill Watch.
[   14.213052] systemd[1]: Starting systemd-rfkill.service - Load/Save RF Kill Switch Status...
[   14.268084] systemd[1]: Started systemd-journald.service - Journal Service.
[   14.408905] systemd-journald[429]: Received client request to flush runtime journal.
[   19.663123] Adding 970748k swap on /var/swap.  Priority:-2 extents:64 across:33091584k SS
[   21.848493] systemd[589]: memfd_create() called without MFD_EXEC or MFD_NOEXEC_SEAL set
[   22.197154] enc28j60 spi0.0 eth0: link down
[   22.197196] enc28j60 spi0.0 eth0: multicast mode
[   22.228940] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[   23.294391] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save disabled