Skip to content

Latest commit

 

History

History
130 lines (89 loc) · 4.29 KB

README.md

File metadata and controls

130 lines (89 loc) · 4.29 KB

NOTE NOTE NOTE

If you are using a modern version of rasbian (ie stretch), then please visit: https://github.com/peebles/rpi3-wifi-station-ap-stretch

RASPBERRY PI 3 - WIFI STATION+AP

Running the Raspberry Pi 3 as a Wifi client (station) and access point (ap) from the single built-in wifi.

Its been written about before, but this way is better. The access point device is created before networking starts (using udev) and there is no need to run anything from /etc/rc.local. No reboot, no scripts.

Use Cases

The Rpi 3 wifi chipset can support running an access point and a station function simultaneously. One use case is a device that connects to the cloud (the station, via a user's home wifi network) but that needs an admin interface (the access point) to configure the network. The user powers on the device, then logs into the access point using a specified SSID/password. The user runs a browser and connects to the access point IP address (or hostname), which is running a web server to configure the station network (the user's wifi).

Another use case might be to create a guest interface to your home wifi. You can configure the client side with your wifi particulars, then configure the access point with a password you can give out to your guests. When the party's over, change the access point password.

/etc/network/interfaces

source-directory /etc/network/interfaces.d

auto lo
iface lo inet loopback

iface eth0 inet manual

allow-hotplug wlan0
iface wlan0 inet manual
    wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf

allow-hotplug uap0
auto uap0
iface uap0 inet static
    address 10.3.141.1
    netmask 255.255.255.0

/etc/udev/rules.d/90-wireless.rules

ACTION=="add", SUBSYSTEM=="ieee80211", KERNEL=="phy0", \
    RUN+="/sbin/iw phy %k interface add uap0 type __ap"

Manually invoke the rule.

Execute the command below. This will also bring up the uap0 interface. It will wiggle the network, so you might be kicked off (esp. if you are logged into your Pi on wifi). Just log back on.

/sbin/iw phy phy0 interface add uap0 type __ap

Set up the client wifi (station) on wlan0.

Create /etc/wpa_supplicant/wpa_supplicant.conf. The contents depend on whether your home network is open, WEP or WPA. It is probably WPA, and so should look like:

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
country=GB

network={
    ssid="_ST_SSID_"
    scan_ssid=1
    psk="_ST_PASSWORD_"
    key_mgmt=WPA-PSK
}

Replace _ST_SSID_ with your home network SSID and _ST_PASSWORD_ with your wifi password (in clear text).

Now to activate this, run the following command:

wpa_cli reconfigure

Install the packages you need for DNS, Access Point and Firewall rules.

apt-get update
apt-get install hostapd dnsmasq iptables-persistent

/etc/dnsmasq.conf

interface=lo,uap0
no-dhcp-interface=lo,wlan0
bind-interfaces
server=8.8.8.8
dhcp-range=10.3.141.50,10.3.141.255,12h

/etc/hostapd/hostapd.conf

interface=uap0
ssid=_AP_SSID_
hw_mode=g
channel=6
macaddr_acl=0
auth_algs=1
ignore_broadcast_ssid=0
wpa=2
wpa_passphrase=_AP_PASSWORD_
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP

Replace _AP_SSID_ with the SSID you want for your access point. Replace _AP_PASSWORD_ with the password for your access point. Make sure it has enough characters to be a legal password! (8 characters minimum).

/etc/default/hostapd

DAEMON_CONF="/etc/hostapd/hostapd.conf"

Now restart the dns and hostapd services

systemctl restart dnsmasq
systemctl restart hostapd

Bridge AP to cient side

This is optional. If you do this step, then someone connected to the AP side can browse the internet through the client side.

echo "net.ipv4.ip_forward=1" >> /etc/sysctl.conf
echo 1 > /proc/sys/net/ipv4/ip_forward
iptables -t nat -A POSTROUTING -o wlan0 -j MASQUERADE
iptables -A FORWARD -i wlan0 -o uap0 -m state --state RELATED,ESTABLISHED -j ACCEPT
iptables -A FORWARD -i uap0 -o wlan0 -j ACCEPT
iptables-save > /etc/iptables/rules.v4

That's it, you should be good to go. You should not have needed to reboot your Pi, but if you do then everything you did will remain in place and functional.