Skip to content

Latest commit

 

History

History
192 lines (157 loc) · 7.85 KB

FLASHING.md

File metadata and controls

192 lines (157 loc) · 7.85 KB

Flashing esp-link

Hardware configuration

This firmware is designed for any esp8266 module. The recommended connections for an esp-01 module are:

  • URXD: connect to TX of microcontroller
  • UTXD: connect to RX of microcontroller
  • GPIO0: connect to RESET of microcontroller
  • GPIO2: optionally connect green LED to 3.3V (indicates wifi status)

The recommended connections for an esp-12 module are:

  • URXD: connect to TX of microcontroller
  • UTXD: connect to RX of microcontroller
  • GPIO12: connect to RESET of microcontroller
  • GPIO13: connect to ISP of LPC/ARM microcontroller or to GPIO0 of esp8266 being programmed (not used with Arduino/AVR)
  • GPIO0: optionally connect green "conn" LED to 3.3V (indicates wifi status)
  • GPIO2: optionally connect yellow "ser" LED to 3.3V (indicates serial activity)

If your application has problems with the boot message that is output at ~74600 baud by the ROM at boot time you can connect an esp-12 module as follows and choose the "swap_uart" pin assignment in the esp-link web interface:

  • GPIO13: connect to TX of microcontroller
  • GPIO15: connect to RX of microcontroller
  • GPIO1/UTXD: connect to RESET of microcontroller
  • GPIO3/URXD: connect to ISP of LPC/ARM microcontroller or to GPIO0 of esp8266 being programmed (not used with Arduino/AVR)
  • GPIO0: optionally connect green "conn" LED to 3.3V (indicates wifi status)
  • GPIO2: optionally connect yellow "ser" LED to 3.3V (indicates serial activity)

If you are using an FTDI connector, GPIO12 goes to DTR and GPIO13 goes to CTS (or vice-versa, I've seen both used, sigh).

The GPIO pin assignments can be changed dynamically in the web UI and are saved in flash.

Initial serial flashing

Download the latest release or use the user1.bin and user2.bin files that are produced by the build process. You will need to flash the bootloader, the firmware, blank wifi settings, and init data. Detailed instructions are provided in the release notes.

Important: the firmware adapts to the size of the flash chip using information stored in the boot sector (address 0). This is the standard way that the esp8266 SDK detects the flash size. What this means is that you need to set this properly when you flash the bootloader. If you use esptool.py you can do it using the -ff and -fs options. See the end of this page for instructions on installing esptool.py.

The short version for the serial flashing is:

  • flash boot_v1.X.bin from the official SDK or from the release tgz to 0x00000
  • flash blank.bin from the official SDK or from the tgz to 0x3FE000
  • flash esp_init_data_default.bin from the official SDK or from the tgz to 0x3FC000
  • flash user1.bin to 0x01000
  • be sure to use the commandline flags when flashing the bootloader to set the correct flash size
  • some of the addresses vary with flash chip size

After the initial flashing if you want to update the firmware it is recommended to use the over-the-air update described further down. If you want to update serially you only need to reflash user1.bin.

32Mbit / 4Mbyte module

On Linux using esptool.py this turns into the following for a 32mbit=4MByte flash chip, such as an esp-12 module typically has (substitute the appropriate release number and bootloader version number):

curl -L https://github.com/jeelabs/esp-link/releases/download/v2.2.3/esp-link-v2.2.3.tgz | \
    tar xzf -
cd esp-link-v2.2.3
esptool.py --port /dev/ttyUSB0 --baud 230400 write_flash -fs 32m -ff 80m \
    0x00000 boot_v1.5.bin 0x1000 user1.bin \
    0x3FC000 esp_init_data_default.bin 0x3FE000 blank.bin

I use a high baud rate as shown above because I'm impatient, but that's not required.

4Mbit / 512Kbyte module

curl -L https://github.com/jeelabs/esp-link/releases/download/v2.2.3/esp-link-v2.2.3.tgz | \
    tar xzf -
cd esp-link-v2.2.3
esptool.py --port /dev/ttyUSB0 --baud 460800 write_flash -fs 4m -ff 40m \
    0x00000 boot_v1.5.bin 0x1000 user1.bin \
    0x7C000 esp_init_data_default.bin 0x7E000 blank.bin

The -fs 4m -ff40m options say 4Mbits and 40Mhz as opposed to 32Mbits at 80Mhz for the 4MByte flash modules. Note the different address for esp_init_data_default.bin and blank.bin (the SDK stores its wifi settings near the end of flash, so it changes with flash size).

For 8Mbit / 1MByte modules the addresses are 0xFC000 and 0xFE000.

Updating the firmware over-the-air

This firmware supports over-the-air (OTA) flashing for modules with 1MByte or more flash, so you do not have to deal with serial flashing again after the initial one! The recommended way to flash is to use make wiflash if you are also building the firmware and ./wiflash if you are downloading firmware binaries.

The resulting commandlines are:

ESP_HOSTNAME=192.168.1.5 make wiflash

or assuming mDNS is working:

ESP_HOSTNAME=esp-link.local make wiflash

or using wiflash.sh:

./wiflash.sh <esp-hostname> user1.bin user2.bin

The flashing, restart, and re-associating with your wireless network takes about 15 seconds and is fully automatic. The first 1MB of flash are divided into two 512KB partitions allowing for new code to be uploaded into one partition while running from the other. This is the official OTA upgrade method supported by the SDK, except that the firmware is POSTed to the module using curl as opposed to having the module download it from a cloud server. On a module with 512KB flash there is only space for one partition and thus no way to do an OTA update.

If you need to clear the wifi settings you need to reflash the blank.bin using the serial method.

The flash configuration and the OTA upgrade process is described in more detail in FLASH.md.

Installing esptool.py on Linux

On Linux use esptool.py to flash the esp8266. If you're a little python challenged then the following install instructions might help:

  • Install ez_setup with the following two commands (I believe this will do something reasonable if you already have it):

     wget https://bootstrap.pypa.io/ez_setup.py
     python ez_setup.py
    
  • Install esptool.py:

     git clone https://github.com/themadinventor/esptool.git
     cd esptool
     python setup.py install
     cd ..
     esptool.py -h
    

Installing esptool.py on Windows

Esptool is a pythin pgm that works just fine on windows. These instructions assume that git and python are available from the commandline.

Start a command line, clone esptool, and run python setup.py install in esptool's directory (this step needs to be done only once):

> git clone https://github.com/themadinventor/esptool.git
Cloning into 'esptool'...
remote: Counting objects: 268, done.
emote: Total 268 (delta 0), reused 0 (delta 0), pack-reused 268
Receiving objects: 100% (268/268), 99.66 KiB | 0 bytes/s, done.
Resolving deltas: 100% (142/142), done.
Checking connectivity... done.

> cd esptool

> python setup.py install
running install
...
...
...
Finished processing dependencies for esptool==0.1.0

Download and unzip the latest esp-link release package, and start a commandline in that directory. The command to run is pretty much the same as for linux. Adjust the path to esptool and the COM port if you don't have the ESP on COM12. 460800 baud worked just fine for me, writing at ~260kbit/s instead of ~80kbit/s.

>python "../esptool/esptool.py" --port COM12 --baud 115200 write_flash \
  --flash_freq 80m --flash_mode qio --flash_size 32m \
  0x0000 boot_v1.6.bin 0x1000 user1.bin \
  0x3FC000 esp_init_data_default.bin 0x3FE000 blank.bin
Connecting...
Erasing flash...
Wrote 3072 bytes at 0x00000000 in 0.3 seconds (79.8 kbit/s)...
Erasing flash...
Wrote 438272 bytes at 0x00001000 in 43.4 seconds (80.7 kbit/s)...
Erasing flash...
Wrote 1024 bytes at 0x003fc000 in 0.1 seconds (83.6 kbit/s)...
Erasing flash...
Wrote 4096 bytes at 0x003fe000 in 0.4 seconds (83.4 kbit/s)...

Leaving...